R Series

Two-Stage General Purpose RFI Power Line Filter

UL Recognized
CSA Certified
VDE Approved

Catalog Data Sheet

R Series

The dual T section RFI power line filters provide premium performance at moderate cost. They are well suited for low impedance loads where noisy RFI environments are present. They control pulsed, continuous and/or intermittent interference, providing protection to your equipment from power line noise in addition to protecting the line from equipment noise. The R series dual T type provides low leakage current without deterioration of insertion loss characteristics and at a competitive cost. The ER models meet the low leakage current requirements of VDE portable equipment, and (120 Volt) UL2601 non-patient medical equipment.

Electrical Schematic

Resistor location for reference only

Specifications

Maximum leakage current, each line to ground:
		VR Models	ER Models
	@ 120 VAC 60 Hz	.4 mA	.21 mA
	@ 250 VAC 50 Hz	.7 mA	.36 mA

Hipot rating (one minute):
	line to ground	2250 VDC
	line to line	1450 VDC

Operating Frequency:		50 / 60 Hz

Rated voltage (max.):		250 VAC

Rated Current:		1A to 20A *
		* refer to part number for rating

Minimum insertion loss in dB:
Line to ground in 50 ohm circuit

Current Rating	Frequency - MHz
Current Rating	.15	.5	1	5	10	30

VR Models
1A, 3A	30	65	65	65	65	65
2A, 5A, 10A, 20A	5	44	60	65	65	60
ER Models
1A, 3A	25	60	65	65	65	65
2A, 5A, 10A, 20A	2	35	51	63	60	50

Line to line in 50 ohm circuit

Current Rating	Frequency - MHz
Current Rating	.15	.5	1	5	10	30

VK, ER Models
1A, 3A	-	-	65	60	54	46
2A, 5A, 10A, 20A	-	-	35	60	57	45

Case Styles

R1 (1-15 Amp)

Typical Dimensions
Terminals (5)	.250	Holes (4)	.07 Dia.
	6.35		1.8
Slot	.07 x .16	Mounting Holes (2)	.188 Dia
	1.8 x 4.1		4.78

Typical Dimensions
Wire Leads (min.) :	4.0	Wire Gauge:	18AWG
	101.6
Mounting Holes (2)	.188 Dia
	4.78

10VR6

Typical Dimensions
Terminals (5):	No. 8-32	Torque:	18 ± 2 in. lb.
		Mounting Holes (4)	.188 Dia.
		Mounting Holes (4)	4.78

20VR6

Note: Same layout for 20VR1 adn 20ER1, except .250 [6.35] (5) terminals replace screw terminals of 20VR6

Typical Dimensions
Terminals (5):	No. 8-32	Torque:	18 ± 2 in. lb.
		Mounting Holes (4)	.250 X .156 Dia.
		Mounting Holes (4)	6.35 x 3.96

R7 & R7M (with metric insert)

Typical Dimensions
Terminals (3)	.250	Holes (2)	.07 Dia.
Terminals (3)	6.35	Holes (2)	1.8
Slot	.07 x .16	R7 Inserts	No. 6-32 x 1/4
Slot	1.8 x 4.1	R7 M Inserts	No. M-3 x 5

Recommended Panel Cutouts

tolerance ± .005 [0.13]

Case Dimensions

Part No.	A	B	C	D	E
	(max.)	(max.)	(max.)	± .015	(max.)
	(max.)	(max.)	(max.)	± .38	(max.)
1VR1, 1ER1, 2VR1, 2ER1	3.35	1.81	1.16	2.375	2.78
1VR1, 1ER1, 2VR1, 2ER1	85.1	46.0	29.5	60.33	70.6

1VR3, 1ER3, 2VR3, 2ER3	2.07	1.81	1.16	2.375	2.78
1VR3, 1ER3, 2VR3, 2ER3	52.6	46.0	29.5	60.33	70.6

3VR1, 3ER1, 5VR1, 5ER1	3.85	2.07	1.16	2.938	3.35
3VR1, 3ER1, 5VR1, 5ER1	97.8	52.6	29.5	74.63	85.1

3VR3, 3ER3, 5VR3, 5ER3	2.56	2.07	1.16	2.938	3.35
3VR3, 3ER3, 5VR3, 5ER3	65.0	52.6	29.5	74.63	85.1

3VR7, 3VR7M, 3ER7, 3ER7M	4.33	2.25	1.28	1.575	0.64 †
3VR7, 3VR7M, 3ER7, 3ER7M	110.0	57.2	32.5	40.01	16.3

5VR7, 5VR7M, 5ER7, 5ER7M	4.33	2.25	1.28	1.575	0.64 †
5VR7, 5VR7M, 5ER7, 5ER7M	110.0	57.2	32.5	40.01	16.3

10VR1, 10ER1	3.85	2.07	1.53	2.938	3.35
10VR1, 10ER1	97.8	52.6	38.9	74.63	85.1

10VR3, 10ER3	2.56	2.07	1.53	2.938	3.35
10VR3, 10ER3	65.0	52.6	38.9	74.63	85.1

10VR6	3.96	2.07	1.53	2.938	3.35
10VR6	100.6	52.6	38.9	74.63	85.1

10VR7, 10VR7M, 10ER7, 10ER7M	4.33	2.25	1.53	1.575	0.88 †
10VR7, 10VR7M, 10ER7, 10ER7M	110.0	57.2	38.9	40.01	22.4

20VR1, 20ER1, 20VR6	5.23	3.37	1.53	3.75	4.20
20VR1, 20ER1, 20VR6	132.8	85.6	38.9	95.25	106.7

† ± .02 [.05]

Part Numbers

Click on any part number for distributor stock status and eCommerce Links. For more information refer to the Corcom Part Numbering System reference.

1VR1	1ER1
1VR3	1ER3
2VR1	2ER1
2VR3	2ER3
3VR1	3ER1
3VR3	3ER3
3VR7	3ER7
3VR7M	3ER7M
5VR1	5ER1
5VR3	5ER3
5VR7	5ER7
5VR7M	5ER7M
10VR1	10ER1
10VR3	10ER3
10VR6
10VR7	10ER7
10VR7M	10ER7M
20VR1	20ER1
20VR6

USA Customer Service:	1-800-468-2023
Corcom Products Direct:	1-847-680-7400
Germany:	49-89-6089-0

Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change.