P Series

UL Recognized
CSA Certified
VDE Approved

Catalog Data Sheet

P Series

The P series power entry module offers fuller flexibility of design in a more compact package.

As the first 10 amp module to provide all five power entry functions in one compact design, the CHAMELEON module readily adapts to its environment and the needs of international markets.

• Snap-in or flange mounting
• IEC power line connector
• Both North American and European fusing capabilities
• Two voltage selections
• Optional DPST on/off switch
• Filtering options for general purpose, medical and high-performance applications.

The CHAMELEON modules compact design and modular construction will allow you to select the power entry features you require — without altering the panel cutout. And the Chameleon module, with adapters, will fit any standard panel cutout.

The CHAMELEON module has four filter options.

S models offer protection for general purpose applications where line-to-ground and line-to-line noise must be controlled. The filters are designed to meet low leakage requirements of VDE portable equipment. They are available in current ratings of 3, 6 and 10 amps.

H models provide susceptibility protection without leakage current associated with line-to-ground capacitors and are designed to allow equipment to meet UL 544 for patient care and non-patient care equipment.

Also available is an interconnection block, B models. The block connects the voltage selection terminals of an unfiltered CHAMELEON module with a switch and an IEC connector to reduce external wiring.

L Models – High performance medical filter versions that are designed to help bring most digital equipment (including switching power supplies) into compliance with EN55022, Level B (as well as FCC part 15J, Class B) conducted emissions limits while additionally allowing equipment to meet UL544, UL2601and EN60601 for patient care equipment and non-patient care equipment. They are available with current ratings of 6 and 10 amps. High performance versions are available with horizontal and vertical mounting ears, single voltage, complete can shield with options for switch, fuses and current ratings only. Extenders are not available.

Z Models – High performance filter versions are designed to help bring most digital equipment (including switching power supplies) into compliance with EN55022, Level B (as well as FCC Part 15J, Class B) conducted emissions limits. They are available with current ratings of 6 and 10 amps. High performance versions are available with horizontal and vertical mounting ears, no extenders, single voltage, complete can shield with options for switch, fuses and current ratings only.

See Appendix C for more information on UL544 or UL2601 health care applications.

Note: When using the models with an IEC connector, remember that the leakage current of the companion line cord, GA400, is more significant than that of the filter - which may disqualify this line cord from use in patient care applications.

Electrical Schematic

H Model

S Model

L Model

Z Model

Resistor location for reference only

PE Filter with "A" Shield

Specifications

P Series Part Numbering Schematic

Part numbers are constructed by selecting the alphanumeric character which represents the desired feature

The P series of power entry modules provides a dual voltage selector which is integrated with the fuseholder. To simplify the wiring in each individual application, Tyco Electronics provides dedicated voltage selectors for different voltage selection schemes. The two most popular schemes are the parallel and serial for dual primary transformers and the “DPST switch” for switching mode power supplies (jumper types.) P series products with an “S” as the fifth digit are specifically designed for “jumper” type applications associated with switching mode power supplies. P series products with an “X” as the fifth digit are specifically designed for dual primary transformer applications. The voltage selector installed will allow proper wiring from these applications. No matter what voltage selection scheme is used, wiring is always made to the same four terminals.

X - Dual Primary Transformer Type

S - Jumper Type

Note 1: Jumpers are required if a filter or interconnection module is not used.
Note 2: Location of optional filter. Jumpers are required if a filter or interconnection block is not used

A new feature available on the P series is an RF shield. The metal shield, available on filtered models, provides shielding from radiated emissions and provides an additional RF ground for the filter to the case. The shield is available in two versions, a shield of the filter components (designated by A as the ninth digit) and a complete shield (designated by B as the ninth digit). The A shield covers the filter portion of the module and increases performance of the filter by protecting the components from magnetic coupling. This shield improves RF ground connection to the case while still allowing the use of the P Series extender. The B shield covers the entire power entry module with metal, protecting the equipment from all radiated noise. Used with the filter, the shield provides the most secure protection from RFI noise problems. The B shield cannot be used with any extender.

Another feature of the P series power entry module is a versatile fusing arrangement. Its fuseholder can hold two 1/4” x 1-1/4” or 5 x 20mm fuses. It can also be converted to accept one fuse with a conversion clip that bridges one of the two fuse chambers. The conversion clip is installed on the P Series power entry modules set for single fusing (those with part numbers with an “S” as the sixth digit). Units with a “D” as the sixth digit do not include a conversion clip.

Conversion clip included for use in single fuse applications

Fuseholder shown with 5x20mm fuse

Also available is an interconnection block (B models). The block connects the voltage selection terminals of an unfiltered CHAMELEON module with a switch and an IEC connector to reduce external wiring. Installation of the unfiltered versions of the P series involves wiring of the IEC socket to the switch and the switch to the fuseholder. Labor can be eliminated by ordering the product with an interconnection block. This feature, designated by a BX in the seventh and eighth digits, pre wires the module for easier installation. The wiring is protected with the plastic case to better prevent access to the terminals and connections. The dimensions of this alternative are the same as the filtered versions.

A full range of accessories are available for the P Series. To simplify customer installation wiring can be simplified by ordering a PA100 connector assembly which is pre-wired with 6" of wire lead. See the P Series Accessory page for a complete list of all accessories available for this series.

PA100 Connector Assembly

Case Styles

PS / PSL

STP Files *
PS Unfiltered	PS Filtered	PS with A Shield	PS with B Shield

PE

STP Files *
PE Unfiltered	PE Filtered	PE with A Shield	PE with B Shield

PM

STP Files *
not available at this time		not available at this time
PM Unfiltered	PM Filtered	PM with A Shield	PM with B Shield

PSC / PSJ

Note 1: For snap-in applications, the D sides of the cutou must have a .02 [.508] radius on the installation side.
Snap-in models allow front mouting only. Not recommended for plastic panels

PE High Performance

Refer to PE for cutout drawing and table for PE High Performance dimensions

STP Files *

PE High Performance

PM High Performance

Refer to PM for cutout drawing and table for PM High Performance for dimensions

* .STP files can be imported as 3D models into most CAD systems.
Files are compressed in .zip format for easy download

Removal of Fuseholder

Step One

Using a pocket screwdriver, insert the screwdriver in the slot under the door and gently rotate the screwdriver to unlatch the door. When unlatched, raise the door and proceed with step two.

Step Two

With the door in the raised position, apply the screwdriver at the slot in the end of the fuseholder and gently push down to raise the fuseholder and remove it from the housing.

Download PDF version

Shielding

Shields can be used only with filtered models
Shields add approximately 0.06" to depth
B Sheild may not be used with J or C Extender

Rear View

Case Dimensions