Skip to content
 |  Tyco Electronics Segment Indicator  |   | 
Tyco Electronics - Our commitment. Your advantage.
Visit www.tycoelectronics.com Corcom Products
Home > Series > IEC > EJT

EJT Series

Compact RFI Filter with IEC Connector for Higher Frequency

UL Recognized
CSA Certified
VDE Approved

15EJT - VDE rated at 10 amps, 250 VAC
20EJT - VDE rated at 16 amps, 250 VAC

Catalog Data Sheet

EJT Series

The EJT Series is a power inlet filter designed to attenuate noise up to 1 GHz. This inlet uses an IEC 320/C14 input connector which gives it a maximum rating of 15 amps. The EJT series is flange-mounted with optional outputs of 1/4" terminals or wire leads. This product was designed to address the demand for more noise attenuation at higher frequencies in a compact inlet. Now also available with an IEC 320/C20 connector with a maximum rating of 20 amps.

*15EJT - VDE rated at 10 amps, 250 VAC, 20EJT - VDE rated at 16 amps, 250 VAC

Electrical Schematic

1-15 Amp

20 Amp

Resistor location for reference only

Specifications

Maximum leakage current, each line to ground:
    1-15 Amp 20 Amp
  @ 120 VAC 60 Hz .22mA .20 mA
  @ 250 VAC 50 Hz .38mA .40 mA
     
Hipot rating (one minute):
  line to ground 2250 VDC 1500 VDC
  line to line 1450 VDC 1450 VDC
     
Operating Frequency: 50 / 60 Hz
     
Rated voltage (max.): 250 VAC
     
Rated Current: 1A to 20A *
  * refer to part number for rating
Minimum insertion loss in dB:
Line to ground in 50 ohm circuit
Current Rating Frequency - MHz
.15 .5 1 5 10 30 100 1000
1A 27 33 40 59 65 65 61 14
3A 22 30 34 57 63 69 61 10
6A 13 21 27 51 60 65 69 14
10A 7 14 21 43 52 61 61 14
15A 4 10 15 38 48 63 63 14
20A - 8 15 42 50 60 58 14

Line to line in 50 ohm circuit
Current Rating Frequency - MHz
.15 .5 1 5 10 30 100 1000
1A 10 20 23 43 52 65 45 14
3A 10 20 24 41 51 59 52 17
6A 10 21 24 37 48 65 55 20
10A 10 21 25 28 44 63 53 18
15A 10 20 26 25 36 56 45 23
20A 9 20 26 40 35 48 50 10

Case Styles

EJT1 (1-15 amp version)

Typical Dimensions
Terminals (3) .250 Holes (2) .07 Dia.
6.35 1.8
Slot .07 x .16 Mounting Holes (2)
 .132 Dia
1.8 x 4.1 3.35
    with .260 x 90° countersunk for#4 Flathead Screw

20EJT1

EJT8

Typical Dimensions
Wire Leads (min.) : 4.0 1-15A Wire Gauge: 18AWG /UL1015
101.6

 

20EJT8

Recommended Panel Cutouts

1 to 15A

Tolerance ± .005 [0.13]

20EJT

 

Case Dimensions

Part No. A B C D E F
(max.) (max.) (max.) (max.) (max.) (max.)
1EJT1, 3EJT1,
6EJT1, 10EJT1,
15EJT1		 2.87 1.19 0.875 1.575 1.98  
72.9 30.2 22.2 40.0 50.3  
1EJT8, 3EJT8,
6EJT8, 10EJT8,
15EJT8		 2.23 1.19 0.875 1.575 1.98 0.295
56.6 30.2 22.2 40.0 50.3 7.5
20EJT1 3.8 1.350 1.18 1.654 2.087  
96.52 34.29 29.99 42.01 53.00  
20EJT8 3.2 1.350 1.18 1.654 2.087  
81.28 34.29 29.99 42.01 53.00  

Part Numbers

Click on any part number for distributor stock status and eCommerce Links. For more information refer to the Corcom Part Numbering System reference.

1EJT1 10EJT1
1EJT8 10EJT8
3EJT1 15EJT1
3EJT8 15EJT8
6EJT1 20EJT1
6EJT8 20EJT8
   
Line Cord GA400
Insulating Boot FA601

 
USA Customer Service: 1-800-468-2023
Corcom Products Direct: 1-847-680-7400
Germany: 49-89-6089-0
Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change.